約翰迪爾割草機應用的發動機零件

設備型號	備注
1565	88mm Bore Non Turbo
F1565	88mm Bore Non Turbo
1565	88mm Bore Non Turbo
F1565	88mm Bore Non Turbo
1600	84mm Bore Turbo
1600	84mm Bore Turbo
1600	88mm Bore Non Turbo
1620	88mm Bore Non Turbo
1905	88mm Bore Non Turbo
1505	88mm Bore Non Turbo
1515	88mm Bore Non Turbo
3225B	84mm Bore Non Turbo
3235	84mm Bore Non Turbo
3235A	84mm Bore Non Turbo
3235B	84mm Bore Non Turbo
7700	84mm Bore Turbo & Non Turbo
8000	84mm Bore Turbo & Non Turbo
8400	84mm Bore Turbo & Non Turbo
8500	84mm Bore Turbo & Non Turbo
8700	84mm Bore Turbo & Non Turbo
8800	84mm Bore Turbo & Non Turbo
7400	84mm Bore Turbo & Non Turbo
7500	84mm Bore Turbo & Non Turbo

約翰迪爾 4045T 4.5T 活塞（米） RE59277/RE505100

PowerTech 系列 發動機和設備型號 4045T 4.5T 代碼 4803, 4823 4 缸數 孔徑: 4.19 in 106.5 mm 銷徑 Ø: 1.3750 in (+/- .0002) = 35mm 發動機型號: 4045TT056 4045TF150 4045TT088 4045TT081 連桿（米): R123959 (Machined) (16) R500000 (Fractured) (16) 連桿（米): RE59277 RE505100 (1) 洋馬發動機 農業 3410 3410X 4890 4895 5415 5425 5510 5520 5525 5615 5625 5715 5725 6700 5425N 5510N 5520N 5525N 5625N AKSA APD-AGJ60 APD-AT65 APD-EPAJ65 APD-ULJ65 原裝 4.5L 工程機械 230 LCR 310E (TURBO) 310G (TURBO) 310SE (TURBO) 310SG (TURBO) 315SE 315SG 344H 410E 410G 410J 450H 550H 650H 發電機組 J60U J66K J70U J77K SKID STEER 280 280 Series II

1) 發動機大修包 TRE66093 (點擊查看套件內容) TRE66093A (點擊查看套件內容) (*) (*) w/C. Rod R500000 2) 發動機內部修理套件 TIK66093 (點擊查看套件內容) TIK66093A (點擊查看套件內容) (*) (*) w/C. Rod R500000 活塞缸套組件 TRE507920 (RE515372) 組成: a) TRE515372 b) TRE66820 c) TR123178 d) TR116383 e) TAR65507 f) TM41029 主軸瓦 TRE65165 Std. TRE65911 0.010 TRE65165B 0.020 (8) 需要4片 止推軸承 TRE65168 Std. TRE65912 0.010 TRE65168B 0.020 (8) 需要1片 連桿瓦 TRE65908 Std. TRE65909 0.010 TRE65908B 0.020 (8) 需要4片 1) 前油封 TRE505515 (9) 2) 后油封 TRE44574 3) 齒環 TR114282 (142T) TR28811 (129T) 4) 曲軸 TRE504638 (13) TRE506195 (12) 5) 密封 TH35244 1) 密封圈維修包 TRE501455 2) 襯墊套 TRE66082 3) 氣缸墊 TR116515 4) 機油底殼墊圈 TR97342 (4) TR123352 (3) 5) 氣門室蓋襯墊 TR123542 6) Timing Cover Gsk TR123421 TR123425 1) 連桿襯套 TR123960 x4 2) 連桿螺栓 TR114083 x8 (2) TR501124 x8 (2) 3) 平衡軸襯套 TR115299 x6 4) 凸輪軸襯套 TR119874 x1 5) 凸輪軸 TRE56375 (6) 6) 右平衡軸 TRE500448 7) 左平衡軸 TRE500449 8) 凸輪隨動件 TR123565 x8 1) 氣缸蓋螺釘 TR85363 x18 (5) 2) 緊張輪 TRE518097 (10) TRE68715 (10) 3) 連桿 TRE500002 4) 機油冷卻器 TRE59296 (5 板) TRE56690 (7 板) TRE59298 (9 板) 1) 水泵 TRE500734 (10) TRE504911 (10) 2) 水泵蓋 TRE508566 3) 水泵襯墊 TR123417 4) 凸輪軸襯套 TRE504914 閥門部分 進氣門 TR98062 Std. TR97490 0.015 排氣門 TR90692 Std. TR97492 0.015 1) 插入閥：進氣 TR98063 Std. TR98335 O/S 2) 插入閥：排氣 TR85687 Std. TR93910 O/S 1) 氣門密封 TRE31617 2) 氣門鎖夾 TR91889 1) 彈簧閥 TR26125 2) 旋轉閥 TRE60005 1) 節溫器 TRE522076 180° F (10) TRE528652 180o F (10) TRE540550 180° F (10) TRE64354 180° F (10) 2) 節溫器蓋 TR501130 (10) 3) 水溫傳感器 TRE51774 (10) 4) 水溫傳感器 TRE52722 (10) 5) 油壓傳感器 TRE167207 (10) 6) 曲軸傳感器 TRE519144 (10) 1) 噴油器 TRE60062 (Non Turbo) TRE48786 (Turbo) TRE531436 (11) 2) 試劑盒 TMX504 3) 密封 TR92352 TR48000 火花塞 1) TRE502079 (11 V) 2) TRE504580 x4 (10 V) 3) 空氣加熱器 TRE502668 (12 V) 1) 輸油泵 TRE66153 (7) TRE68345 (14) TRE502513 (15) 2) 電動燃油泵 TAL155607 (10)

強鹿JOHN DEERE柴油機配件、發動機配件、發電機組：
4039DFM,6068SM50 ,RE522528、RE519774、RE532628、RE518176、RE507980、RE518503、RE522515、RE504836、RE509031、RE509032、RE59754、RE507284、RE59754、RE519626、RE518977、RE508202、RE58935、T19044、RE62418、RE62419、RE521248、RE520842、C085004、AR95758、LVA10419、AH128449、RE509672、RE196945、RE191915、RE522688、RE522687、RE519774、RE532628/
強鹿JOHN DEERE柴油機配件、發動機配件、發電機組：
RE507980、RE531703、RE24619、RE187966、RE205726、RE507264、RE504836、RE509036、RE533910、RE532952、RE530107、RE508971、RE523502、RE518520、RE68345、RE53307、RE62240、RE533095、RE502513、RE38009、R30402、RE521538、RE521540、RE62240、P524837、RE60021、RE507236、RE59588、RE549153、RE530870、SE501610、SE501609、RE70960specification oil pump drive shaft—maximum end play   . 0.15 mm (0.006 in.) replace oil pump if end play exceeds specification. rg,rg34710,1227 –19–23oct97–1/1 check drive shaft side movement rg5917 –un–05dec97 checking pump shaft side movement 1. mount dial indicator with indicator plunger resting on one of the hex nut flats. 2. move shaft from side-to-side. if shaft side movement exceeds specification, there is excessive wear in drive shaft bushing and/or drive shaft. specification oil pump drive shaft—maximum side movement    0.17 mm (0.0065 in.) replace oil pump if shaft side movement exceeds specification. ctm86 (20mar01) 02-060-14 powertech? 8.1 l diesel engines — base engine 032001 pn=282 lubrication system repair&adjustment 02 060 15 rg,rg34710,1228 –19–23oct97–1/1 check pumping gear backlash rg5918 –un–05dec97 checking backlash of pumping gear 1. mount dial indicator with plunger resting against side of gear tooth. 2. hold idler gear stationary. slowly rotate drive gear back&forth until contact with idler gear is left. if backlash is not within specification, there is excessive pumping gear wear and/or idler shaft and gear bushing wear. specification oil pump drive gear—backlash  . 0.33—2.00 mm (0.013—0.079 in.) if there is less than 0.33 mm (0.013 in.) backlash, re-clean gears&check backlash again. 3. replace oil pump if pumping gear backlash exceeds 2.00 mm (0.079 in.). rg,rg34710,1229 –19–23oct97–1/1 inspect oil pump drive gear rg6435 –un–05dec97 inspecting pump drive gear note: oil pump does not need to be removed from engine, when inspecting drive gear. inspect drive gear teeth for chips, cracks,/wear. replace as necessary. ctm86 (20mar01) 02-060-15 powertech? 8.1 l diesel engines — base engine 032001 pn=283 lubrication system repair&adjustment 02 060 16 dpsg,ouo1004,845 –19–27apr99–1/1 adjust oil pump set screw rg3509 –un–03nov97 inspecting pump drive gear a—set screw b—oil pump cover c—lock nut important: normally the set screw (a) should not be adjusted; but if the set screw is altered, the following steps should be followed. 1. assemble drive gear&idler gear into pump housing. 2. install oil pump cover (b)&tighten cover-to-housing cap screws to specifications. specification oil pump cover-to-housing— torque   . 41 n?m (30 lb-ft) 3. tighten set screw until it contacts idler shaft. 4. continue to hold set screw&tighten lock nut (c) to specifications. specification oil pump set screw lock nut— torque   . 8 n?m (6 lb-ft) do not overtighten set screw/lock nut. 5. spin drive gear by hand to assure shaft turns freely in housing. readjust set screw if shaft does not turn freely. dpsg,ouo1004,823 –19–21apr99–1/2 install engine oil pump rg9042 –un–28apr99 install oil pump gear&pickup a—oil pump drive gear b—oil pickup tube 1. install gear (a) onto pump&tighten snug using nut and washer. final torque will be accomplished after installing pump. 2. using a new gasket, install oil pickup tube (b) onto oil pump&tighten cap screws to specifications. specification oil pump intake (pickup) tube-to-cover—torque  . 47 n?m (35 lb-ft) ctm86 (20mar01) 02-060-16 powertech? 8.1 l diesel engines — base engine 032001 pn=284 continued on next page lubrication system repair&adjustment 02 060 17 dpsg,ouo1004,823 –19–21apr99–2/2 rg9045 –un–28apr99 oil pump gear rg9044 –un–29apr99 install oil pump outlet tube a—oil pump drive gear b—oil pump outlet tube 3. install new o-ring in groove of oil pump housing and lubricate with clean engine oil. install oil pump outlet tube into oil pump housing. 4. swing oil pump assembly over locating dowels and carefully position assembly onto dowels without applying pressure to/causing binding of outlet tube. important: do not hammer directly on pump housing as it could cause binding of gears. 5. seat pump onto dowels using a hard rubber hammer on outer edge of housing near mounting holes (as shown). make sure drive gear is properly meshed with crankshaft gear&oil pump outlet tubes are properly positioned (with no binding) in o-ring bores. important: some early engines used grade 5 oil pump mounting cap screws. replace these cap screws with new grade 8 cap screws when reinstalling pump. 6. install&tighten oil pump housing-to-cylinder block cap screws to specifications. specification oil pump housing-to-cylinder block—torque  . 42 n?m (31 lb-ft) 7. tighten oil pump drive gear retaining nut to specifications. specification oil pump drive gear retaining nut—torque    54 n?m (40 lb-ft) ctm86 (20mar01) 02-060-17 powertech? 8.1 l diesel engines — base engine 032001 pn=285 lubrication system repair&adjustment 02 060 18 rg,rg34710,1232 –19–23oct97–1/1 remove&install oil pump outlet tube and oil cooler crossover tube adapter rg7221 –un–05dec97 oil cooler crossover tube&adapter a—adapter b—oil cooler cross-over tube remove adapter: 1. remove oil pump (shown removed). see remove engine oil pump earlier in this group. 2. remove two cap screws securing adapter (a) to cylinder block&remove adapter with oil cooler cross-over tube (b). 3. clean all gasket material from mating surfaces and discard. install adapter: note: be sure gasket is positioned so that offset matches adapter to avoid blocking oil passages. 1. lubricate new o-ring with clean engine oil&install adapter (with cross-over tube) using a new gasket. make sure tubes are properly positioned in each o-ring bore. 2. tighten cap screws to specifications. specification oil pump outlet&oil cooler cross-over tube-to-cylinder block adapter (internal)—torque   . 54 n?m (40 lb-ft) 3. install engine oil pump assembly. see install engine oil pump earlier in this group. ctm86 (20mar01) 02-060-18 powertech? 8.1 l diesel engines — base engine 032001 pn=286 lubrication system repair&adjustment 02 060 19 dpsg,ouo1004,914 –19–29jun99–1/1 remove, inspect,&install oil pump pickup tube rg10238 –un–30jun99 oil pickup tube a—screen b—oil pickup tube c—cap screws (3 used) 1. remove oil pan. see remove oil pan earlier in this group. 2. remove cap screws (c)&remove oil pickup tube assembly (b)&gasket. 3. clean&flush tube&pickup screen (a). 4. inspect tube for cracks/restrictions. replace as required. 5. install pickup tube assembly with new gasket and tighten cap screws to specifications. specification oil pump pickup tube cap screws—torque   41 n?m (30 lb-ft) 6. install oil pan. see install engine oil pan later in this group. ctm86 (20mar01) 02-060-19 powertech? 8.1 l diesel engines — base engine 032001 pn=287 lubrication system repair&adjustment 02 060 20 dpsg,ouo1004,824 –19–21apr99–1/2 install engine oil pan rg9544 –un–30apr99 install oil pan a—oil pan gasket b—oil pan c—o-ring d—drain plug all oil pan&cylinder block (including timing gear cover&rear seal housing) gasket sealing surfaces must be free of gasket material/oil,&dry. 1. apply a thin layer of permatex? aviation (form-a-gasket no. 3, ty6299) at timing gear cover-to-cylinder block mating surfaces. 2. apply a thin layer of permatex? aviation (form-a-gasket no. 3, ty6299) at rear oil seal housing-to-cylinder block mating surfaces. 3. position new oil pan gasket (a) on cylinder block. 4. apply a thin layer of permatex? aviation (form-a-gasket no. 3, ty6299) to gasket at same location as cylinder block in step nos. 1, 2 above. important: oil pan cap screws should have only one flat washer&no lockwasher. if cap screws have flat washers with lock washers, discard them and replace with new hardened flat washers. note: locate rear of oil pan flush to ± 0.05 mm (0.002 in.) with rear face of cylinder block. 淮南johndeere約翰迪爾強鹿柴油機油泵供應商,廊坊johndeere約翰迪爾強鹿柴油機充電發電機找哪家,鶴崗約翰迪爾強鹿柴油發動機凸輪軸下襯套一級代理,荊門約翰迪爾強鹿4045柴油機RE65911主軸瓦價格,遼源JohnDeere3029氣門室蓋墊片批發,長沙約翰迪爾柴油機氣門油封T20129找哪家,臨滄強鹿連桿襯套TR114082廠家價格,東營強鹿6081柴油機排氣門哪里買,宜賓強鹿JohndeereTO4039皮帶漲緊輪哪家買,濱州約翰迪爾3029DF128活塞批發價,淮北強鹿柴油機DZ10393活塞襯墊套件代理,阿拉善約翰迪爾氣門室蓋墊片R524497哪家好,湛江約翰迪爾6090柴油機氣門油封批發商,湖州JohnDeere氣門油封T20129代理,鶴壁強鹿曲軸齒輪R104587廠家供應,果洛強鹿R106957凸輪軸批發商,晉城約翰迪爾6081柴油機主軸瓦價格,攀枝花約翰迪爾柴油發電機組電磁閥代理,南昌約翰迪爾柴油發電機配件哪家好,潮州美國JohnDeere啟動馬達RE515843廠家價格,5. carefully install oil pan (b) on cylinder block and tighten all oil pan-to-cylinder block cap screws as follows: a. first tighten 1/2-inch cap screws to the following specification. specification oil pan 1/2 in. cap screws— torque  . 156 n?m (115 lb-ft) b. next tighten 3/8-inch cap screws to specifications. permatex is a registered trademark of loctite corporation. ctm86 (20mar01) 02-060-20 powertech? 8.1 l diesel engines — base engine 032001 pn=288 continued on next page lubrication system repair&adjustment 02 060 21 dpsg,ouo1004,824 –19–21apr99–2/2 specification oil pan 3/8 in. cap screws— torque  . 68 n?m (50 lb-ft) 6. trim oil pan gasket flush at rear surface of cylinder block&oil pan. 7. retighten all oil pan cap screws as follows: a. first retighten 3/8-inch cap screws to specification. b. finally, retighten all 1/2-inch cap screws to specification. 8. install pan drain plug (d) using a new o-ring (c) and tighten to specifications. specification oil pan drain plug aluminum pans—torque  . 101 n?m (75 lb-ft) 9. some engine oil pans may be equipped with an elbow&drain hose. note: on engines equipped with elbow fittings and drain hose, the threads&sealing surfaces must be free of any oil film to insure an effective seal. apply a light coat of loctite? 592 to fittings except for the leading one to three threads. if equipped, tighten elbow lock nut to the following specification. specification oil pan elbow lock nut— torque  . 81 n?m (60 lb-ft) loctite is a registered trademark of loctite corp. ctm86 (20mar01) 02-060-21 powertech? 8.1 l diesel engines — base engine 032001 pn=289 lubrication system repair&adjustment 02 060 22 rg,rg34710,1234 –19–23oct97–1/2 tighten cap screws on front frame/oil sump (8000 series tractors) note: refer to illustration on following page. 1. be sure all four sump-to-block locating dowels are in place. important: do not apply gasket sealant to gasket, front frame/oil sump, trimmed edges of timing gear cover gasket, oil seal housing gasket, or cylinder block mating surfaces. before installing engine, be sure mating surfaces of engine&front frame/oil sump are clean&dry. 2. install front frame/oil sump-to-cylinder block gasket. 3. carefully lower engine block onto front frame/oil sump locating dowels. 4. install all 3/8 in.&1/2 in. cap screws in their appropriate locations as shown by a-f. 5. tighten all 1/2 in. cap screws to specifications. specification front frame/oil sump (8000 tractors) 1/2 in. cap screws— torque  . 133 n?m (98 lb-ft) tighten all 3/8 in. cap screws to specifications. specification front frame/oil sump (8000 tractors) 3/8 in. cap screws— torque  . 58 n?m (43 lb-ft) 6. re-tighten all 3/8 in. cap screws to specifications. re-tighten all 1/2 in. cap screws to specifications. 7. apply clean engine oil to new o-ring for bottom drain plug&install drain plug, if removed. tighten plug to specifications. specification oil pan drain plug cast iron pans (sumps)—torque   47 n?m (35 lb-ft) note: refer to tm1575 (8000 tractors—repair) for engine installation instructions after servicing engine oil pump assembly. (for tracks models, refer to tm1621.) continued on next page ctm86 (20mar01) 02-060-22 powertech? 8.1 l diesel engines — base engine 032001 pn=290 lubrication system repair&adjustment 02 060 23 rg,rg34710,1234 –19–23oct97–2/2 rg7223 –un–28apr99 front frame/oil pump for 8000 tractors a—0.3775 x 7.500 in. (2 used) c—0.500 x 6.000 in. (8 used) e—0.500 x 2.500 in. (6 used) f—0.375 x 1.875 in. (2 used) b—0.500 x 4.000 in. (4 used) d—0.375 x 2.250 in. (2 used) ctm86 (20mar01) 02-060-23 powertech? 8.1 l diesel engines — base engine 032001 pn=291 lubrication system repair&adjustment 02 060 24 ctm86 (20mar01) 02-060-24 powertech? 8.1 l diesel engines — base engine 032001 pn=292 group 070 cooling system repair&adjustment 02 070 1 dpsg,ouo1004,848 –19–27apr99–1/3 replace bearings in heavy-duty, adjustable fan drive assembly rg8754 –un–02dec97 heavy-duty adjustable fan drive assembly a—fan hub/pulley c—snap ring e—shaft g—pipe plug b—grease seal d—ball bearing (2 used) f—bearing housing h—support plate to disassemble fan drive: 1. remove belts&remove fan. remove fan drive assembly from engine. 2. clamp fan hub/pulley (a) in a soft-jawed vise. support fan hub (so it does not fall to floor), and remove cap screw securing hub to shaft (e). remove fan hub. 3. remove pipe plug (g), grease seal (b),&snap ring (c). discard seal&snap ring. 4. remove shaft with bearings (d) by lightly tapping with a rubber mallet/brass hammer. 5. remove bearings from shaft using a press and discard bearings. 6. thoroughly clean&inspect shaft&bearing housing (f) for cracks/any other damage. measure parts&compare with specifications given below. specification adjustable fan drive housing—id 71.999—72.025 mm (2.8346—2.8356 in.)    adjustable fan drive shaft— od 35.001—35.017 mm (1.3780—1.3786 in.)   . adjustable fan drive bearing— id. 34.987—35.013 mm (1.3774—1.3785 in.)   . od 71.987—72.013 mm (2.8341—2.8351 in.)   . replace parts that are cracked/not within specification. ctm86 (20mar01) 02-070-1 powertech? 8.1 l diesel engines — base engine 032001 pn=293 continued on next page cooling system repair&adjustment 02 070 2 dpsg,ouo1004,848 –19–27apr99–2/3 rg8754 –un–02dec97 heavy-duty adjustable fan drive assembly a—fan hub/pulley c—snap ring e—shaft g—pipe plug b—grease seal d—ball bearing (2 used) f—bearing housing h—support plate to assemble fan drive: 1. pack inner&outer bearings (d) with ty6333 or ty6347 high temperature grease. apply clean engine oil to bearing i.d.&shaft o.d. 2. support end of shaft (e)&install bearings against shoulder. apply force to bearing inner race only. 3. support bearing housing (f) on a firm flat surface with bearing bore in the upward position. 4. install bearing&shaft assembly into housing. small end of shaft should extend through housing. 5. determine proper snap ring (c) thickness needed to obtain specified end play. specification adjustable fan drive shaft— end play    0.10 mm (0.004 in.) 6. install snap ring in housing groove. visually inspect snap ring installation for proper seating in housing groove. 7. apply a thin coat of clean engine oil to o.d. of seal casing (b)&to seal lips. install seal in housing bore until metal casing is to specified depth below housing face. specification adjustable fan drive housing seal—depth flush-to-0.50 mm (0.020 in.) below housing face   . 8. apply clean engine oil to i.d. of fan hub/pulley (a). support end of shaft through pipe plug hole in bearing housing&push onto other end of shaft until it bottoms against shoulder. ctm86 (20mar01) 02-070-2 powertech? 8.1 l diesel engines — base engine 032001 pn=294 continued on next page cooling system repair&adjustment 02 070 3 dpsg,ouo1004,848 –19–27apr99–3/3 note: if engine i湖州強鹿24v柴油泵市場報價,白銀約翰迪爾強鹿密封圈修理包RE528400的價格,汕尾強鹿Johndeere風扇總成找哪家,伊犁強鹿柴油機水泵總成RE521503找哪家,阜陽約翰迪爾6J-1854拖拉機發動機配件廠家供應,陽江JohnDeere凸輪軸上襯套供應商,北海約翰迪爾6081發動機齒環批發價,無堂劃分域JOHNDEERE強鹿柴油機增壓器RE503722廠家供貨,撫順強鹿6068缸套陽水圈誠信推薦,昆明約翰迪爾re525523強鹿柴油濾芯代理,成都約翰迪爾發動機曲軸齒批發,綿陽JohnDeere節溫器AR48675供貨商,香港島強鹿6090柴油發動機曲軸齒環代理,柳州強鹿柴油機氣門導管R517011廠家供應,雙鴨山約翰迪爾6068柴油機曲軸齒輪廠家價格,昌吉約翰迪爾曲軸RE535300哪里買,南昌約翰迪爾強鹿4045柴油機止推軸承RE65168誠信推薦,海東約翰迪爾6081發動機連桿批發,來賓johndeere約翰迪爾強鹿柴油機活塞環廠家供貨,淮南強鹿6090柴油機小修包公司,赤峰johndeere約翰迪爾強鹿柴油發動機起動機RE70960價格行情,隨州約翰迪爾活塞銷卡簧E1343FN誠信推薦,臺中JOHNDEERE迪爾3029D發動機配件批發價,上海JohnDeere加大止推軸承瓦RE61253哪里買,s equipped with a fan/hub pulley-to-fan spacer, tighten hub/pulley-to-spacer cap screws to the following specification. specification fan/hub pulley-to-fan spacer cap screws—torque   . 60 n?m (45 lb-ft) 9. install washer&cap screw. tighten cap screw to specifications. specification fan hub/pulley-to-fan shaft— torque  . 80 n?m (60 lb-ft) 10. apply loctite? 592 pipe sealant to threads of pipe plug (g). install&tighten plug in bearing housing. 11. install fan drive assembly onto support plate (h). 12. install support plate assembly onto engine and tighten cap screws to the following specifications. fan drive support plate-to-engine—specification 5/16-in. mounting cap screws (to injection pump access cover)—torque    24 n?m (18 lb-ft) 5/16-in. mounting cap screws (all others)—torque  . 35 n?m (26 lb-ft) 3/8-in. mounting cap screws— torque  . 61 n?m (45 lb-ft) 1/2-in. mounting cap screws— torque  . 101 n?m (74 lb-ft) 13. install fan&belts&adjust tension. see replacing fan/alternator v-belt in operator’s manual. loctite is a registered trademark of loctite corp. ctm86 (20mar01) 02-070-3 powertech? 8.1 l diesel engines — base engine 032001 pn=295 cooling system repair&adjustment 02 070 4 dpsg,ouo1004,809 –19–27apr99–1/2 replace bearings in coolant manifold-mounted, fixed fan drive assembly rg8753 –un–28nov97 fixed fan drive assembly a—coolant manifold b—fan pulley d—bearing shaft installed e—fan spacer hub1 c—bearing shaft dimension to disassemble fan drive: 1. remove three coolant manifold-to-cylinder head cap screws. remove coolant manifold (a)&fan pulley (b) assembly from cylinder head&lift to dislodge coolant bypass pipe from manifold. 2. support front face of coolant manifold&use a press to push bearing (c)&pulley out of manifold. 3. support front face of fan pulley&push bearing out of pulley,&fan spacer (if equipped). discard bearing. 4. thoroughly inspect coolant manifold&pulley for cracks/damage. measure parts&compare readings with specifications shown. replace parts as necessary. important: support fan pulley on a flat, firm surface&press only on bearing outer race to prevent damage to the bearing. 5. install new bearing into pulley until outer race bottoms in bore of pulley. end of shaft will extend through bearing stop. coolant manifold-mounted fixed fan drive specifications coolant manifold-mounted fixed fan drive specifications— specification fixed fan drive shaft—od 25.387—25.400 mm (0.9995—1.0000 in.)    fixed fan drive bearing—od 47.612—47.625 mm (1.8745—1.8750 in.)    1in some applications, bearing is pressed into hub (e). the fan spacer&pulley are then bolted to hub. in some applications, the fan spacer is press-fit into the pulley. dimension (d) is the same for all applications. ctm86 (20mar01) 02-070-4 powertech? 8.1 l diesel engines — base engine 032001 pn=296 continued on next page cooling system repair&adjustment 02 070 5 dpsg,ouo1004,809 –19–27apr99–2/2 fixed fan drive pulley (bearing end)—id 47.576—47.612 mm (1.8731—1.8745 in.)   . fixed fan drive pulley (fan spacer end )2—id 49.485—49.518 mm (1.9482—1.9495 in.)    fan spacer2—o.d. 49.457—49.483 mm (1.9471—1.9481 in.)   . fixed fan drive manifold—i.d. 25.336—25.362 mm (0.9975—0.9985 in.)    fixed fan drive shaft (installed)—dimension from manifold mounting face to end of shaft 32.51—32.77 mm (1.280—1.290 in.)   . to assemble fan drive: important: support coolant manifold on machined surface&press only on inner shaft to prevent damage to bearing. 1. on units with a press-fit fan spacer, press spacer (e) into pulley (b) to the following depth. specification adjustable fan drive housing seal—dep廣元強鹿柴油發電機組啟動機信息,佳木斯強鹿柴油機小修包IK6090廠家價格,牡丹江強鹿柴油機RE504914油泵哪里買,撫州強鹿柴油發動機凸輪軸市場報價,張家口約翰迪爾強鹿活塞包批發,上海強鹿柴油發電機組發電機信息,佳木斯約翰迪爾3029連桿R80032廠家批發,濮陽強鹿加大連桿瓦RE529318A供應商,大慶JohnDeere缸套R116236哪家好,長治約翰迪爾R122191誠信推薦,宜賓約翰迪爾發動機氣缸墊哪家好,海西約翰迪爾傳感器RE519144批發,連云港約翰迪爾挖掘機啟動機廠家供應,阿克蘇約翰迪爾強鹿柴油發動機電子燃油泵一級代理,赤峰約翰迪爾燃油泵RE502513誠信推薦,眉山強鹿TRE520768活塞缸套組件廠家批發,保定約翰迪爾4039DF008活塞供應商,亳州強鹿原廠進口缸套活塞供應商,潮州約翰迪爾聯合收割機發動機電腦板廠家批發,th flush-to-0.50 mm (0.020 in.) below housing face   . 2. press bearing shaft (c) into coolant manifold (a) to the following specification. specification fixed fan drive bearing shaft—depth 33.31—33.57 mm (1.311—1.322 in.) below manifold mounting surface    hold coolant manifold firmly&turn fan pulley by hand to be sure bearings rotate freely. 3. install a new gasket&o-rings. insert coolant bypass pipe in manifold&install assembly onto locating pin in front face of cylinder head. tighten cap screws to specifications. specification fixed fan drive (coolant manifold mounted) cap screws—torque   . 60 n?m 45 (lb-ft) 4. install fan&belts. refer to appropriate operator’s manual for proper belt tensioning. 2units with press-fit fan spacer only. rg41165,000006d –19–30jan01–1/10 fan drive assembly use the following tables to determine proper fan drive height. continued on next page ctm86 (20mar01) 02-070-5 powertech? 8.1 l diesel engines — base engine 032001 pn=297 coolingKEY PART NO. PART NAME QTY SERIAL NO. F F F REMARKS
1 RE47431 FUEL LINE 1 X NO. 6
2 RE47430 FUEL LINE 1 X NO. 5
3 RE47429 FUEL LINE 1 X NO. 4
4 R120185 BOLT 5 X
R58186 CLAMP 10 X
R120181 STRAP 5 X
R120182 STRAP 5 X
5 RE47428 FUEL LINE 1 X NO. 3
6 RE502930 FUEL LINE 1 X NO. 2
7 RE502929 FUEL LINE 1 X NO. 1
8 R120186 BOLT 2 X
R71212 CLAMP 1 X
R120183 STRAP 1 X
R120184 STRAP 1 X
R59297 HALF CLAMP 2 X
9 R71212 CLAMP 1 X
R59297 HALF CLAMP 2 X
R74030 CLAMP 1 X
R74804 CLAMP 1 X
R120186 BOLT 2 X
R120183 STRAP 1 X
R120184 STRAP 1 X
10 R120185 BOLT 1 X
R59297 HALF CLAMP 2 X
R120183 STRAP 2 X
11 RE55662 ABSORBER 1 X
12 24H1884 WASHER 1 X 13/32" X 13/16" X 0.120"
13 19M7166 CAP SCREW 1 X M10 X 20
14 RE61593 INJECTION NOZZLE 6 X (A) (ROBERT BOSCH)
15 R84472 WASHER 6 X 7.360 X 18.160 X 2 MM (0.290" X 0.715"
X 0.079")
16 R504057 O-RING 6 087550- X
17 RE501970 ADAPTER 1 X
18 R51937 TUBE NUT 1 X
19 AR85519 PLUG 1 X
20 RE500803 FUEL LINE 1 X
21 R79604 TUBE NUT 1 X
(A) 1 ORANGE DOT
1 POINT ORANGE
1 ORANGEFARBENER PUNKT
1 PUNTO ARANCIONE
1 PUNTO ANARANJADO
1 ORANGEFAERGAD PUNKT
KEY PART NO. PART NAME QTY SERIAL NO. F F F REMARKS
1 R60277 SNAP RING 1 X
2 R375R O-RING 1 X
3 R60279 NUT 1 X
4 R60278 SNAP RING 1 X
5 .. NOZZLE HOLDER 1 X (SUB RE61593)
6 R83720 WASHER 1 X 1.02 MM (.0402")
R83721 WASHER 1 X 1.08 MM (.0425")
R83722 WASHER 1 X 1.12 MM (.0441")
R83723 WASHER 1 X 1.18 MM (.0465")
R83724 WASHER 1 X 1.22 MM (.0480")
R83725 WASHER 1 X 1.28 MM (.0504")
R83726 WASHER 1 X 1.30 MM (.0512")
R83727 WASHER 1 X 1.38 MM (.0543")
R83728 WASHER 1 X 1.42 MM (.0559")
R83729 WASHER 1 X 1.48 MM (.0583")
R83730 WASHER 1 X 1.50 MM (.0591")
R83731 WASHER 1 X 1.58 MM (.0622")
R83732 WASHER 1 X 1.60 MM (.0630")
R83733 WASHER 1 X 1.68 MM (.0661")
R83734 WASHER 1 X 1.70 MM (.0669")
R83735 WASHER 1 X 1.78 MM (.0701")
R83736 WASHER 1 X 1.82 MM (.0717")
R83737 WASHER 1 X 1.88 MM (.0740")
R83738 WASHER 1 X 1.90 MM (.0748")
R83739 WASHER 1 X 1.98 MM (.0780")
7 R108699 SPRING 1 X
8 R108700 SEAT 1 X
9 R108701 PLATE 1 X
10 RE42306 INJECTION NOZZLE 1 X (7 X .240)
11 R127176 NUT 1 X
12 R84472 WASHER 1 X
13 RE61593 INJECTION NOZZLE 6 X (A) (ROBERT BOSCH)
(A) (1) ORANGE DOT
(1) POINT ORANGE
(1) ORANGEFARBENER PUNKT
(1) PUNTO ARANCIONE
(1) PUNTO ANARANJADO
(1) ORANGEFAERGAD PUNKT
KEY PART NO. PART NAME QTY SERIAL NO. F F F REMARKS
1 R51936 SEALING WASHER 2 X
2 RE504748 FUEL LINE 1 X
3 RE502650 FITTING 1 X
4 R121164 GEAR 1 X
5 R121195 CAP SCREW 4 X
6 R114130 STUD 4 X
7 M72490 WASHER 4 X
8 14H1090 NUT 4 X
9 R79060 O-RING 1 X
10 AR88903 ELBOW FITTING 1 X
11 R67264 PACKING 1 X
12 RE509065 OIL LINE 1 X (SUB FOR RE60577)
13 T18012 ELBOW FITTING 1 X
14 RE505268 FUEL INJECTION PUMP 1 X (A) (BOSCH) (ALSO ORDER R504886 AND (2)
19M8826)
(A) "SEE YOUR AUTHORIZED PUMP REPAIR STATION FOR PARTS NOT LISTED"
CONSULTEZ VOTRE REPARATEUR DE POMPE AGREE POUR LES PIECES NON CATALOGUES
NICHT GEZEIGTE TEILE VON PUMPENWERKSTAT BEZIEHEN.
PER LE PARTI NON ELENCATE, RIVOLGETEVI AL CENTRO AUTOIZZATO DI RIPARAZIONE POMPA
CONSULTE CON SU ESTACION AUTORIZADA RE PEPARACIONES DE BOMBA.
RAADGOER MED EN AUTORISERAD PUMPSERVICICVERKSTAD BETRAEFFANDE EJ UPPTAGNA